Login to post Please use English characters only. Then you can run the installation driver CD that came with the drive. It’s worth a thousand words. So to put Xp on the computer i went into the bios and try to change the setting Older optical drives used the 40 conductor, newer ones use the 80 conductor, but there is no harm done using the On reboot you should see a new menu option to enter the RAID controller settings.

Uploader: Zolonos
Date Added: 2 July 2008
File Size: 61.25 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 75148
Price: Free* [*Free Regsitration Required]

MS Phoenix BIOS won’t talk to OCZ SATA II drive on VIA VT SATA RAID.

If you cannot clear the setting in the BIOS, there is a set of three pins between the battery and the corner of the board, move the jumper to the raif position and start the system to clear the BIOS settings.

Reformat your hard disk you will lose anything you had not backed up and install XP presumably from a CD you have. If you are simply booting from a “normal” stand-alone disk into Windows and then using a RAID array as riad data storage system, the RAID driver installation can be done any time after Windows is running as you set up the new storage system. There are several versions of RAID.

MSI MS (KM3M-V) driver Motherboards software versions

Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered. When you are asked where you want to install Windows 7 you should see that the 2 RAID hard disks are now visible as just 1 drive.

Recent Drivers  2WIRE 2700HG-B DRIVER DOWNLOAD

Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two. The RAID system uses multiple number of hard disks to give a fast and fault tolerant storage using several disk controllers.

Also many of the new motherboards offer multiple drive configurations such as RAID. I set bios to raid and choose proper disc as boot I assume, you are talking about combining 2 hard drives to create more disk space on your system. Now turn the power switch back on for a few with the cord unplugged, then shut it off again. These steps assume you are performing a clean Windows 7 install rather than an upgrade, and they might differ depending on your system set-up, but the general principles should be the same.

I can’t seem to access the BIOS when the computer’s booting. Then you can run the installation driver CD that came with the drive. Add Your Answer Tips for a great answer: Click “repair your computer” and click the “load drivers” button.

It’s definitely for the adventurous knowledgeable techie.

I have windows 7 ultimate installed. It’s worth a thousand words.

MSI MS-7061 (KM3M-V) VGA Drivers

While the end connectors are rais same, only 40 conductors, the 80 conductor cables have interlaced grounding, which allows them to transfer data at a higher speed. This has nothing to do with the operating system! This should be set before you install them, because it is very hard to get at the jumpers afterwards: Instant Repair Help over the Phone 6ya.

Recent Drivers  DELL Y8029 DRIVER DOWNLOAD

Keeps saying “Error code “. Lately during the filling cycle water hammer is occurring.

Not finding what you are looking for? The blue connector at the far end of the cable, away from the other two goes into the motherboard. Note that these are a different size and shape from the SATA power cables. You can’t download it through the official Asus support page yet, but there’s a topic in the Asus support forum with a link.

Enter the key combination when prompted to get to the RAID controller menu.

Also make sure the power supply can handle mz-7061 extra current, this depends on the other stuff such as drives and video card you already have in the machine. This can be upgraded to the limit the computer will support, a good reference for capability of your system and a good source for purchase ms7-061 www. Add a partition to the new drive so Windows with be able to recognise it. This is almost the same as the process to repair a damaged RAID1 array by replacing one faulty drive with a new one and rebuilding the array.